! NCP.MEM - Network Control Program help file
! NCP.RNO - DSR source file of the help file
! Updated February 24, 1982. Son VoBa.
!
! The .MEM file should reside in the HLP: directory of the running system.
!
! Each NCP command has an entry in this file. The entries must be
! alphabetically ordered and must be preceeded with an "*" in column 1.
!
! Additional entries may be added to this help file, but with care.
*
NCP enables an operator to perform network control functions like
changing parameters, gathering information, down-line loading, up-line
dumping, triggering bootstrap, testing link and network, and zeroing
counters.
Help for a specific command may be obtained with the HELP command as
follows:
NCP> HELP keyword [additional parameter]
For instance, if you wish additional information about the CANCEL
command you would type "HELP CANCEL"
*CANCEL
CANCEL is used to remove a command from the queue before processing
begins. You can check the status of the command with the SHOW QUEUE
command.
*CLEAR
CLEAR is used to clear parameters of an entity from the volatile data
base. Additional information available
CLEAR CIRCUIT
CLEAR EXECUTOR NODE
CLEAR LINE
CLEAR LOGGING
CLEAR NODE
*CLEAR CIRCUIT
CLEAR CIRCUIT is used to clear the volatile circuit parameters for
the circuit(s) identified in the command.
*CLEAR EXECUTOR NODE
CLEAR EXECUTOR NODE is used to reset the EXECUTOR to the node on
which the NCP program is running. Note that this command does not
return the executor to the value in the permanent data base.
*CLEAR LINE
CLEAR LINE is used to clear the volatile line parameters for the
line(s) identified in the command.
*CLEAR LOGGING
CLEAR LOGGING is used to control the logging of events, both the
events that will be logged and where they will be logged.
*CLEAR NODE
CLEAR NODE is used to clear the volatile parameters of the node
identified as node-id or set as EXECUTOR.
*DEFINE
DEFINE is used to modify values in the permanent data base of the
identified entity. Additional information available
DEFINE CIRCUIT
DEFINE LINE
DEFINE LOGGING
DEFINE NODE
*DEFINE CIRCUIT
DEFINE CIRCUIT is used to set the permanent circuit parameters for
the circuit(s) identified in the command.
*DEFINE LINE
DEFINE LINE is used to set the permanent line parameters for the
line(s) identified in the command.
*DEFINE LOGGING
DEFINE LOGGING is used to control where the events are logged (event
sinks) and which events get logged.
*DEFINE NODE
DEFINE NODE is used to set the permanent parameters for the node
identified as node-id or set as EXECUTOR.
*DUMP
DUMP is used to store a copy of the target's memory image in a dump
file at the host node.
*ENTER
ENTER is used to enter an alternative command processor for an
application type.
*EXIT
EXIT is used to leave NCP command level and return to the TOPS-20
monitor command level.
*HELP
HELP allows you to display the function and format of any NCP
command. The format is
NCP> HELP keyword [additional parameters]
where keyword can be any one of the following NCP commands:
CANCEL CLEAR DEFINE DUMP ENTER EXIT HELP
LIST LOAD LOOP PURGE PUSH RETURN SET
SHOW TAKE TELL TRIGGER ZERO
*LIST
LIST is used to display information from the permanent data base.
*LOAD
LOAD is used to load the system image file from one node to a remote
node in the network
*LOOP
LOOP is used to request a node level loopback test. The node
specified in the command is the node to be connected TO; that is,
the node that will loop back the data. This may be the local node or
a remote node.
*PURGE
PURGE is used to clear parameters of an entity from the permanent
data base. Additional information available
PURGE CIRCUIT
PURGE EXECUTOR NODE
PURGE LINE
PURGE LOGGING
PURGE NODE
*PURGE CIRCUIT
PURGE CIRCUIT is used to clear the permanent circuit parameters for
the circuit(s) identified in the command.
*PURGE EXECUTOR NODE
PURGE EXECUTOR NODE is used to reset the executor in the permanent
data base to the local node.
*PURGE LINE
PURGE LINE is used to clear the permanent line parameters for the
line(s) identified in the command.
*PURGE LOGGING
PURGE LOGGING is used to control the logging of events, both the
events that will be logged and where they will be logged.
*PURGE NODE
PURGE NODE is used to clear the permanent parameters of the node
identified as node-id or set as EXECUTOR.
*PUSH
PUSH is used to leave the NCP command level and enter the TOPS-20
monitor command level. The POP command is used to return to the NCP
command level.
*RETURN
RETURN is used to return to the OPR command level.
*SET
SET is used to modify values in the volatile data base of the
identified entity. Additional information available
SET CIRCUIT
SET LINE
SET LOGGING
SET NODE
*SET CIRCUIT
SET CIRCUIT is used to set the volatile circuit parameters for the
circuit(s) identified in the command.
*SET LINE
SET LINE is used to set the volatile line parameters for the line(s)
identified in the command.
*SET LOGGING
SET LOGGING is used to control where the events are logged (event
sinds) and which events get logged.
*SET NODE
SET NODE is used to set the volatile parameters for the node
identified as node-id or set as EXECUTOR.
*SHOW
SHOW is used to display information from the volatile data base.
*TAKE
TAKE is used to execute a series of NCP commands from a specified
command file.
*TELL
TELL NODE is used as a prefix to designate the node that is to
process the command. The prefix is effective only for the single
command that immediately follows. Although the access information is
optional, the node specified as node-id may refuse to accept the
command.
Using the TELL NODE prefix is more efficient than a combination of
SET EXECUTOR and CLEAR EXECUTOR commands when only one command is to
be given to a node.
*TRIGGER
TRIGGER is used to attempt to cause the target node (the node to be
loaded) to send a load request to the executor. If the load request
is sent successfully, the load proceeds automatically.
*ZERO
ZERO is used to generate a counters zeroed event that causes counters
to be logged. The counters are then set to zero. The counters
affected are those associated with the specified entity.
.KJOB